bounty hunter tracker iv review

bounty hunter tracker iv metal detector-working in dynamic mode. This means that for metal detection, search ring should be in motion. When using the bounty hunter tracker iv metal detector, running in static mode, the Detection over the ring of objects, objects under the ring, can not be detected.

Three modes of operation.

 bounty hunter tracker iv has three modes of operation:

 (all metal), “TONE”, “FULL” (tone discrimination and discrimination). After switching on the appliance and set the desired sensitivity (the regulator “Sensitivity”), proceed with the selection of the operating mode.

All metals : (3-way switch in middle position) in this mode will be detected all types of metals: iron, steel, aluminum, bronze, copper, gold. Application: search of rarities, finding gold, treasure hunts, surveyors.

Complete discrimination (DISC): (3-way switch in the left position) in this mode, most of the trash metal will automatically “removed”, ignored by changing the position of the regulator “DISC/NOTCH” toward “high” (max) to increase the range of discrimination.

bounty hunter tracker iv Metal Detector

Discrimination by tone (TONE): (3-way switch in right position) in this mode the characteristic dual (high or low) “beep” and automatically remove iron makes finding jewelry, non-ferrous metals the most effective. This mode also allows you to get “broken” signal for the aluminium trash, which the regulator “DISC/NOTCH” should be set in Center (about 12.00). Having a 2-tone and definition of “broken” signal for garbage, you can determine the type of detected metal in the ground according to the issued instrument signals. Application: search for coins, jewelry, work at littered areas.

In this mode, the detected metal objects is determined by the signal of low or high tones. Change the level of discrimination (the regulator “DISC/NOTCH”) upwards – you will increase the range of objects observed the sound woofer.

Thus, small coins will issue a low tone, large-tall aluminum plugs will have low tone or jogged tone. Bending (up-down) tone makes trash easily recognizable. Sensitivity is slightly reduced,  “TONE” mode.

Metal detector bounty hunter tracker iv achieve maximum detection depth, use the mode  (all metal); the regulator “DISC/NOTCH” Rotate counterclockwise until the end; then the regulator “Sensitivity” (sensitivity) turn the hourly until the arrows cod. For removal of cod or erroneous signals to “beep”, slowly rotate the pointer back counterclockwise.

Metal detector bounty hunter tracker iv-special features:

bounty hunter tracker iv metal detector finds a coin to a depth of 20 cm. (coin 5 copecks), the large objects at a depth of 90 cm. (the car).

Metal detector features automatic installation of the balance on the ground, without loss of sensitivity.

Automatic installation of balance on Earth:

 This setting allows you to work in almost all types of soil, minimizing the effect of soil. This is particularly effective when searching for gold nuggets or while working at marine beaches. In the mode  (all metal)-a three-way switch in middle position; in this mode, the device will respond to gold nuggets even the mineralized sands.

Getting started:

 To turn on the unit turn left “Sensitivity” knob until it clicks into place. ATTENTION: the appliance will be switched to remain silent; He begins to issue alerts when moving metal objects under Search ring. Inserting the device by clicking the left knob, you have set the minimum sensitivity. Turning the knob clockwise towards the “HIGH”, the degree of sensitivity will increase, allowing for the detection of small or deep objects. If the device produces crack, slowly reduce the sensitivity until the noise stops.

For best results, use the highest possible sensitivity. Usually the sensitivity above in the modes “DISC” or “TONE” (respectively left or right  mode switch).

POSSIBLE DIFFICULTIES

 Your device produces error signals when searching.

Possible causes: metal detector bounty hunter tracker iv

-Sensitivity regulator “SENSITIVITY” is set at too high a level. Gradually decrease the sensitivity, while fake alerts will not disappear.

-Search the ring you want to drive a slow movements.

 -sometimes signals can be caused by strong mineralization of soil, the presence in the ground of rusted objects; If the signal after the repeated movements does not repeat, this means that the object is not of interest.

-the existence of natural or industrial origin of electromagnetic field may cause malfunction of the device.

THE USE OF METAL DETECTORS

bounty hunter tracker iv review

bounty hunter tracker iv review

The most popular application of metal detectors:

Search coins:

Required settings:

1 three-way toggle switch-in) left position (DISC mode).

2) regulator of discrimination (“DISC/NOTCH”)-“3:0”.

Only silver, copper, bronze will be decided. Gold items will be ignored. Different in composition and size of the coins will give different signals.

The hunt for rarities, relics:

The data subjects are historical objects, often large in size, the most correct is the initial training-study of literature, the archives, memoirs of contemporaries, etc.

Required settings:

1) Way in the central position – the switch (mode “ALL METALS”).

2) regulator of discrimination (“DISC/NOTCH”)-“LOW” position.

The hunt for hidden treasures:

Typically, this is some specific items presented in a jar, box, small safe, bag, etc.

Required settings:

1) Way in the central position – the switch (mode “ALL METALS”).

2) regulator of discrimination (“DISC/NOTCH”)-“LOW” position.

The hunt for jewelry:

This category of objects can be found everywhere. Beaches, parks, school yards-everywhere jewelry can be lost by one person, and therefore found the other.

Required settings:

1) three-way switch is in the right position (“TONE” mode).

2) regulator of discrimination (“DISC/NOTCH”)-“12:0”.

You should start digging only when high or low signal. “Broken” signal means-metal stuff.

Gold rings will cause low signal tone. Please note caps from beer cans can also cause low signal tone.

Silver will cause high signal tone. Chains are difficult to detect.

Find gold nuggets, gold mining locations:

Looking for nuggets of gold mining areas and along rivers, downstream from the flushing of golden sand.

Required settings:

1) Way in the central position – the switch (mode “ALL METALS”).

2) regulator of discrimination (“DISC/NOTCH”)-“LOW” position.

Find gold nuggets, gold mining locations:

Looking for nuggets of gold mining areas and along rivers, downstream from the flushing of golden sand.

Required settings:

1) Way in the central position – the switch (mode “ALL METALS”).

2) regulator of discrimination (“DISC/NOTCH”)-“LOW” position.

Switch target Analyzer allows you to get information about the detected metal object and its conductivity (iron, gold, silver). Position the arrows on the display depends on the conductivity of metal.

Dynamic modes “all metals”, “sound discrimination», «IRON discrimination» switches tumbler.

2 handles for smoothly changing sensitivity level and the level of discrimination.

2-tone and jogged sound signals, you can identify the type of metal in the ground.

Standard ¼ “headphone jack.

Battery power status indicator (power 9 volt, Crone 2 PCs.).

Coil 20 cm;

Weight in working order-1.35 kg.