READ THE INSTRUCTIONS IN THIS MANUAL BEFORE USING THE INSTRUMENT!
Congratulations for the excellent choice of LASER metal detector one of purpose and light tools that exists today.
ASSEMBLY
The first required Assembly and tighten with the two screws supplied with the larger diameter tube to the control box (in the two threads already prepared), insert the smaller diameter tube into the greater, preparing it to desired length and secure with the clamp. Third, invite the coil round to researching smaller diameter tube into the hole spiral wrapping swing the coil wire around two tubular and plugging the connector into the socket located in front of the control box. Attention! do not dry wire curves near the coil mount. Fourth and final assembly insert the 9 V battery square in housings designed behind the control box. And the tool is ready for use and research. NOTE: the 95% of the problems of metal detectors are due to low battery or cable break coil (caused by tearing against branches or bushes when searching so be careful!). A good idea is to remove the batteries from their container for extended periods of inactivity.
DESCRIPTION OF THE COMMANDS IN THE METAL DETECTOR
Sensitivity knob serves the instrument on and off and to adjust its power of penetration into the soil. Must be always set to maximum (full clockwise-rotated) except in cases where due to radio interference the firm might give the speaker. Then power should be slightly lower.
Discriminated level knob is used to adjust the degree of discrimination of metals when it set the function selector to disc by 3 positions (research and finding only precious metals: gold, silver, brass, aluminum, lead, etc. … more you rotate clockwise the knob and you leave also noble metals, usually goes to less than half scale)
Function modes switch, serves for setting the desired search mode. By pressing on the disc and discrimination will be automatically function overlooked pieces of iron, steel, bottle caps, foils etc …, pressing toward all metals intervenes the all metal and metal detector will detect any type of metal. This function is also used to center the object detected. Greater will be the audible sound in speaker and better will be the tracking object. If you push the selector to batt. Tests run the test battery, which indicates good battery for over 3 tone beep.
Tuner knob is used to adjust the signal level of audio threshold which makes the tool, for having a good sound recognition it is recommended to adjust the knob until you hear a slight sibilio almost nil. This function is used only with a tool set for search all metals.
RULES OF USE OF THE METAL DETECTOR
The LASER is a motion detector, i.e. the search coil must be continually move from right to left and vice versa for the presence of metals. Support coil on the ground and press the disc. Rotate all in sensitivity knob clockwise to get maximum search depth.
Search all metal press the lever towards ALL METAL In this way you will detect all metals of any kind both small and large.
Research on discrimination (which is the one and only search precious metals or ferrous metals but nevertheless fairly large in size) press lever to DISC and turn the knob clockwise discriminate bringing it up about 1/4 of the scale. Turn knob discriminate specifies the right degree of discrimination. At the beginning it is preferable to take lower this threshold. (from experience you may want to do some more digging to avoid objects left behind preziosi). Now you can start your search with the infinity researching coil (every inch that the coil is far from the land corresponds to an inch lost in depth) and swinging big arches from Direction left and vice versa, taking about 2 seconds for each pass.
laser rapier manual metal detector
Strategic research for better results: set the instrument in all metal and the sound threshold to a level slightly audible (in this way you will have maximum power and sensitivity of the instrument. Rotate as the search coil to the right and to the left and pay attention to every variation of suno. Each variation test whether this is good material from dig by placing the selector on disc. If the detector sounds again in the case of noble metal and dig if the detector does not sound more question of ferrous metal . However, the personal experience and research technique gives the best results.
WHAT TO DO AND WHAT NOT TO DO!
Do not drown the control box, and do not leave it in the car under sunlight.
Do not leave too short the cable close to the coil, and protect it against the branches.
Not to slam violently the coil against trees, stones, ect …. it goes through the perfect balance.
Make sure the coil connector socket is connected well.
Use a detector in certain prohibited locations it is illegal. Make sure that the site before making a search. Do not damage the nature in all its forms, and always respect the environment must be closing any gaps. Respect the private property of others, and always ask the owner first.
laser rapier manual metal detector In the category Metal Detectors more articles and learn more information about laser rapier manual metal detector Reviews Price Specifications Features Image manuals videos Accessories All this in metal detectors for gold.
Tags: Laser, laser rapier, manual
Comments
Post a Comment