Bounty Hunter Tracker IV Metal Detector

 Bounty Hunter Tracker IV metal detector–distinctive features:

Tracker IV metal detector finds a coin to a depth of 20 cm. (coin 5 copecks), large-sized objects at depths of up to 90 cm.

The metal detector is the automatic installation of balance on the ground, without loss of sensitivity.

Switch target Analyzer allows you to get information about the detected metal object and its conductivity (iron, gold, silver). Position the arrows on the display depends on the conductivity of metal.

Dynamic mode “all metals”, “sound discrimination” discrimination “,” IRON switches tumbler.

2 handles for a smooth change in the level of sensitivity and discrimination level.

2-tone and broken sound signals to identify the type of metal in the ground.

Standard ¼ “headphone jack.

Battery power status indicator (power 9 volt, 2 Crown piece).

Coil 20 cm;

Weight in working order-1.35 kg.

MODES OF OPERATION

 Tracker IV metal detector-working in dynamic mode. This means that metal detection, search ring should be in motion. When using the Tracker IV metal detector, running in static mode, the pronosite over the ring of objects, objects under the ring, can not be detected.

Three modes of operation.

Tracker IV has three modes of operation:

 “ALL METAL” (all metal), “TONE”, “FULL” (full tone discrimination and discrimination). After switching on the appliance and set the desired sensitivity (regulator “Sensitivity”), proceed with the selection of the operating mode.

All metals (ALL METAL): (or three position control switch in middle position) in this mode will be detected all types of metals: iron, steel, aluminum, bronze, copper, gold. Application: searching for rarities, searching for gold, treasure hunts, earthwork.

Complete discrimination (DISC): (or three position control switch in the left position) in this mode, most of the metal trash automatically deleted “Bude”, ignored by changing the position of the regulator “DISC/NOTCH” toward “high” (max) to increase the range of discrimination.

Discrimination by tone (TONE): (or three position control switch in right position) in this mode the characteristic dual (high or low) “BIP” and automatically remove iron makes finding jewelry, non-ferrous metals the most effective. This mode also allows you to get “doit” signal for the aluminium trash, which the regulator “DISC/NOTCH” needs to be installed in the Centre (approximately 12.00). Having a 2-tone and definition of “broken” signal for garbage, you can determine the type of detected metal in the ground according to the issued instrument signals. Application: search for coins, jewelry, work at littered areas.

In this mode, the detected metal objects is determined by the signal of low or high tones. Change the level of discrimination (the regulator “DISC/NOTCH”) upwards – you will increase the range of objects observed sound low tone. Thus, small coins will issue a low tone, large-tall aluminum plugs will have low tone or bending tone. Bending (up-down) tone makes the garbage easy recognizable. Slightly reduce the sensitivity, kogdamispol′zuete “TONE” mode. Metal detector Bounty Hunter Tracker IV achieve maximum detection depth, use the mode “ALL METAL” (all metal); regulator “DISC/NOTCH” Rotate counterclockwise until the end; then the regulator “Sensitivity” (sensitivity) turn arrow hourly until the Cod. To eliminate cod or erroneous signals to “BIP”, slowly rotate the pointer back counterclockwise.

Automatic installation of balance on Earth:

This setting allows you to operate practically in all types of soil, minimizing the influence of soil sil′nomineralizovannoj. This is especially useful when searching for gold nuggets or while working at marine beaches. In the mode “ALL METALS” (all metal) or three position control switch in middle position; in this mode, the device will respond to gold nuggets even the mineralized sands.

Getting started:

To switch on the appliance, turn the left switch “Sensitivity” until you hear a click. Warning: when turning on the device will remain silent; He will start to issue alerts when moving metal objects under the ring search. Inserting the device by clicking the left knob, you have set the minimum sensitivity. Turning the knob clockwise towards the “HIGH”, the degree of sensitivity will increase, allowing for detection of small objects or a few deep. If the machine makes loud banging, slowly reduce the sensitivity until the noise stops.

For best results, use the highest possible sensitivity. Usually the higher sensitivity modes “DISC” or “TONE”.

POSSIBLE DIFFICULTIES

Your device produces erroneous signals when searching.

Possible causes: metal detector Bounty Hunter Tracker IV

-Sensitivity regulator “SENSITIVITY” is set at too high a level. Gradually decrease the sensitivity, while fake alerts will not disappear.

-Search the ring you want to drive a slow movements.

-Sometimes, the signals can be caused by severe soil salinity in the soil, presence of rusted objects; If the signal does not repeat after repeat movements, it means that the object is not of interest.

-the existence of natural or industrial origin of electromagnetic field may cause malfunction of the device.

THE USE OF METAL DETECTORS

The most popular application of metal detectors:

Search for coins:

Required settings:

1) or three position control switch is in the left position (“DISC”).

2) regulator of discrimination (“DISC/NOTCH”)-“3:0”.

Only silver, copper and bronze would be determined. Gold items will be ignored. Different in composition and size of the coins will give different signals.

The hunt for rarities, relics:

The data subjects are historical objects, often large in size, is the most appropriate initial training and the study of literature, the archives, memoirs of contemporaries, etc.

Required settings:

1) or three position control switch in central position (mode “ALL METALS”).

2) regulator of discrimination (“DISC/NOTCH”) – “LOW” position.

The hunt for hidden treasures:

Typically, this is some specific items presented in a jar, box, small safe, bag, etc.

Required settings:

1) or three position control switch in central position (mode “ALL METALS”).

2) regulator of discrimination (“DISC/NOTCH”) – “LOW” position.

The hunt for jewelery:

This category of objects can be found everywhere. Beaches, parks, school yards and around jewellery may be lost by one person, and therefore found the other.

Required settings:

1) or three position control switch is in the right position (“TONE” mode).

2) regulator of discrimination (“DISC/NOTCH”)-“12:0”.

You should start digging only when high or low signal. “Signal” means a Bending-metal stuff.

Gold rings will cause low signal tone. Note the cover of beer cans can also cause low signal tone.

Silver will cause high signal tone. Chains are difficult to detect.

Find gold nuggets, gold mining in the field:

Look for the nuggets in gold mining areas and along rivers, downstream from where flushing of golden sand.