bounty hunter commando metal detector In the category Metal Detectors more articles and learn more information about bounty hunter commando metal detector Reviews Price Specifications Features Image manuals videos Accessories All this in metal detectors for gold.
bounty hunter commando metal detector – easy to read user equipped with just two knobs and a selector switch, appliance, however, allows us to solve or reduce the impact of two of the most difficult aspects of the use of metal detectors – select the desired mode and balance setting on the ground.
bounty hunter commando metal detector – easy-to-use device that does not require special training, a high-performance under various conditions. Easy to read user equipped with just two knobs and a selector switch, appliance, however, allows us to solve or reduce the impact of two of the most difficult aspects of the use of metal detectors – select the desired mode and balance setting on the ground.
bounty hunter commando metal detector
Both of these points in Commando solved automatically. The device will operate in extreme conditions, including salt saturated sea beach and conditions of major gold mining areas of debris foreign particles, without the need for operator adjustments and without much loss in sensitivity.
–bounty hunter commando metal detector – features of the device: Detects coin at a depth of up to 20 cm large objects to a depth of 90 cm
The device has an automatic–balance setting on the ground, without loss of sensitivity.
Dial–purpose analyzer provides information on metal detection and its conductivity (iron, gold, silver). Position of the arrow on the display depends on the conductivity of the metal.
–Dynamic modes: «ALL METAL» – Discrimination – «TONE» toggle switch.
-2 Handles for smooth changes in the level of sensitivity and the level of discrimination.
2–tone and broken sound signals allows to identify the type of metal in the ground.
Standard–1/4 “headphone jack.
Battery–status indicator (batteries Crohn 9 Volt, 2 pcs.)
–Operating weight – 1.35 kg.
bounty hunter commando metal detector – Metal working in dynamic mode. This means that for the detection of metal search coil should be in motion. When using a metal detector in a static mode, sweeps over the ring of objects, objects under the ring, can not be detected.
Three modes of operation.
Commando has three modes of operation:
«ALL METAL» «TONE», «FULL» (tone discrimination and full discrimination). After turning on the device and set the desired sensitivity (controller “Sensitivity”), proceed to the selection of the operating mode.
Mode “All metals» : (three-position switch in the middle position) in this mode will detect all types of metals such as iron, steel, aluminum, bronze, copper, gold. Application: find rarities, search for gold, treasure hunts, land surveying work.
“Full discrimination» (DISC): (three-position switch to the left) in this mode most of the trash will automatically “removed,” Repositioning the regulator ignored “DISC / NOTCH” toward “high” (maximum) will increase the range of discrimination.
Mode “Discrimination in tone» (TONE): (three-position switch to the right) in this mode is characterized by a dual (high or low) “beep” and the automatic removal of iron makes the search for jewelry, precious metals most effective. This mode also allows you to get the “intermittent“ signal for aluminum trash, which the regulator “DISC / NOTCH” must be installed in the center (about 12.00) With 2-tone and definition of “intermittent” beep garbage, you can determine the type of the detected metal in the ground according to published by the instrument signals. Application: find coins, jewelry, work in high trash areas.
bounty hunter commando metal detector
In this mode, the detection of metal objects is determined by the signal high or low tone.
Change the level of discrimination – regulator “DISC / NOTCH”, upward – you increase the range of facilities, low-pitched sound celebrated. At the same time, small coins, will publish a low tone, large – tall, aluminum caps will have a low tone or intermittent tone. Intermittent (up-down) makes garbage tone easily recognizable. Slightly reduce the sensitivity when using mode “TONE”.
bounty hunter commando metal detector
For maximum depth of target detection mode, use the (all metals); regulator “DISC / NOTCH” to turn fully counterclockwise; then the regulator (sensitivity) hourly turn arrow pops up. To eliminate false signals cod or “beep“, gradually turn the pointer back counterclockwise.
Automatic installation of the balance on the ground:
This setting allows you to work in almost all types of soil, minimizing the impact of strongly soil. This is especially useful when searching for gold nuggets or working on sea beaches. In the “ALL METAL” (all metals) – three-way switch in the middle position; in this mode the device will respond to even the gold nuggets on mineralized sands.
Getting Started:
To turn on the lights, turn left “Sensitivity” until it clicks. NOTE: when the device will remain silent; he starts beep when moving metal objects below the search ring. Turn on the device by clicking on the left slider, you set the minimum sensitivity. Turn the knob clockwise towards “HIGH”, the degree of sensitivity will increase, allowing for detection of small or deeply buried objects. If the device emits a cracking sound, slowly reduce the sensitivity until the noise stops.
bounty hunter commando metal detector
For best results, use the highest possible sensitivity. Usually at higher sensitivity modes “DISC” or “TONE” (respectively left or right position selector switch)
Possible difficulties.
bounty hunter commando metal detector
Your metal detector emits false signals when searching – Causes:
– Sensitivity Control “SENSITIVITY” is set at too high a level. Gradually decrease the sensitivity, while false signals disappear.
– Exploratory ring need to drive slow movements.
– Sometimes the signals may be caused by strong ground mineralization, the presence in the soil of rusty objects; if the signal after repeated movements is not repeated, it means that the object is not of interest.
–The presence of natural or industrial origin of the electromagnetic field can cause the device.
Your metal detector produced unstable pulsating sounds instead of the normal signal – Causes:
– Operating nearby or other metal you are near power lines that may cause electromagnetic interference.
Your metal detector emits a constant signal or constant repeating signal – Causes:
– Usually means that the batteries are discharged much, replace it with a new alkaline batteries.
